 |
| Place of Origin: | GERMANY |
| Brand Name: | Lenze |
| Certification: | CE |
| Model Number: | EVS9321-EP |
| Minimum Order Quantity: | 1pcs |
|---|---|
| Packaging Details: | carton |
| Delivery Time: | in stock |
| Payment Terms: | T/T, Western Union, MoneyGram |
| Supply Ability: | 100pcs/week |
| LENZE: | LENZE | EVS9321-EP: | EVS9321-EP |
|---|---|---|---|
| GERMANY: | GERMANY | Material: | Iron |
| Color: | Black | Temperature: | 20-90 |
| Wire: | Wire | Dimension: | 80mm |
| You enable a parameter by setting the corresponding bit to "1".The parameters for the 16 digital output channels are located in data records 64 to 79 and | |
| are assigned as follows: ● Data record 64 for channel 0 ● Data record 65 for channel 1 |
|
| Data record 78 for channel 14 ● Data record 79 for channel 15 |
Data record structure
The figure below shows the structure of data record 64 for channel 0 as an example. The
structure is identical for channels 1 to 15. The values in byte 0 and byte 1 are fixed and must
not be changed.
You enable a parameter by setting the corresponding bit to "1".
You can change the parameters of the High Speed Counter in RUN. The WRREC instruction
is used to transfer the parameters to the High Speed Counter using data record 128.
If errors occur when transferring or validating parameters with the WRREC instruction, the
High Speed Counter continues operation with the previous parameter assignment. The
STATUS output parameter then contains a corresponding error code. If no error has
occurred, the length of the data actually transferred is entered in the STATUS output
parameter.
You will find a description of the "WRREC" instruction and the error codes in the STEP 7
(TIA Portal) online help.
Data record structure
The following table shows you the structure of data record 128 with the counter channel. The
values in byte 0 to byte 3 are fixed and must not be changed. The value in byte 4 may only
be changed by parameter reassignment and not in RUN modeReserved bits must be set to 0
2) Must be set to 1 for the activation of the diagnostic interrupts "Missing supply voltage L+, "Illegal A/B signal ratio" and
"Hardware interrupt lost0001B:
Counting: Between comparison value 0 and high counting
limit;
Measuring: Measured value >= Comparison value 0
0010B:
Counting: Between comparison value 1 and low counting
limit; Measuring: Measured value <= Comparison
value 1
0010B:
Counting: Between comparison value 0 and low counting
limit; Measuring: Measured value <= Comparison
value 0
0011B:
Counting: At comparison value 1 for one pulse duration;
Measuring: Reserved
0011B:
Counting: At comparison value 0 for one pulse duration;
Measuring: Reserved
0100B: Between comparison value 0 and 1 0100B: Reserved
0101B:
Counting: After set command from CPU until comparison
value 1;
Measuring: Reserved
0101B:
Counting: After set command from CPU until comparison
value 0;
Measuring: Reserved
0110B:
Counting: Reserved
Measuring: Not between comparison value 0 and 1
0110 to 1111B: ReservedBehavior of
count value
after Capture
(DI0):
Edge selection (DI0): Level selection
(DI0):
Reserved =
0 1)
Set function of the DI (DI0):
00B: Reserved 000B: Gate start/stop (level-controlled)
01B: On a rising edge 0B: Active at
high level
001B: Gate start (edge-controlled)
10B: On a falling edge 010B: Gate stop (edge-controlled)
0B: Continue
counting
11B: On rising and falling
edge
1B: Active at
low level
011B: Synchronization
100B: Enable synchronization at signal N
1B: Set to
start value
and continue
