This resolution does not apply to temperature values. The digitalized temperature values are
the result of a conversion in the analog module.
Table C- 1 Resolution of the analog values
Resolution in bits
including sign
ValuesThe tables below set out the digitized representation of the input ranges by bipolar and
unipolar input ranges. The resolution is 16 bitsThe following tables list the decimal and hexadecimal values (codes) of the possible voltage
measuring rangThe following tables list the decimal and hexadecimal values (codes) of the possible current
measuring ranges.
Table C- 7 Current measuring range ±20 mA
The following tables list the decimal and hexadecimal values (codes) of the supported
thermocouples.
Table C- 14 Thermocouple type B
Error events initiate a diagnostics entry and trigger a diagnostics interrupt if configured
accordingly.
Table C- 21 Measured values for wire break diagnosticsre break" diagnostics enabled
• "Overflow/Underflow" diagnostics
enabled or disabled
("Wire break" diagnostics takes priority
over "Overflow/Underflow" diagnostics)
32767 7FFFH "Wire break" or "Open circuit" diagnostics
alarm
• "Wire break" diagnostics disabled
• "Overflow/Underflow" diagnostics
enabled
-32767 8000 H • Measured value after leaving the undershoot
range
• Diagnostics alarm "Low limit violated"
• "Wire break" diagnostics disabled
• "Overflow/Underflow" diagnostics
disabledn the product "Digital Modules, Analog Modules, Technological Modules, Communication
Modules and Power Supply Modules of the SIMATIC , ET 200MP", Copyright
AG, 2013 - 2014 (hereinafter "Product"), the following Open Source Software is
used either unchanged or in a form that we have modified, and additionally the other License
Software noted below.
Liability for Open Source Software

Open Source Software is provided free of charge. We are liable for the Product including
Open Source Software contained in accordance with the license conditions applicable to the
Product. Any liability for use of Open Source Software beyond the program flow intended for
the Product is explicitly excluded.
We do not provide any technical support for the Product if it has been modified.This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of products
Note the following:
WARNING
products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by . Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the