with "1" to "0", max. 4 ms
For interrupt inputs
• Configurable No
for technological functions
• Configurable No
Cable length
shielded, max. 1000 m
unshielded, max. 600 m
Encoders
Connectable encoders
2-wire sensor Yes
• Permitted quiescent current (2-wire sensor),
max.
1.5 mA
Isochronous mode
Isochronous mode (application synchronized up to
terminal)
No
Interrupts/diagnostics/status information
Diagnostics function No
Interrupts
Diagnostics interrupt No
Hardware interrupt No
Diagnostics alarms
Monitoring of supply voltage No
Wire break No
Short-circuit No
Diagnostics indicator LED
RUN LED Yes; green LED
ERROR LED Yes; red LED
Monitoring of supply voltage (PWR LED) No
Channel status display Yes; green LED
For channel diagnostics No
For module diagnostics NoBetween the channels No
Between the channels, in groups of 16
Between the channels and backplane bus Yes
Isolation
Isolation tested with 707 V DC (type test)
Ambient conditions
Ambient temperature during operation
Horizontal mounting position, min. 0 °C
Horizontal mounting position, max. 60 ℃
Vertical mounting position, min. 0 °C
Vertical mounting position, max. 40 °C
Distributed mode
Prioritized startup Yes
Dimensions
Width 35 mm
Height 147 mm
Depth 129 mm
Weights
Weight, approx.The dimensional drawing of the module on the mounting rail, as well as a dimensional
drawing with open front cover, are provided in the appendix. Always observe the specified
dimensions for installation in cabinets, control rooms, etc.If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of products
Note the following:
WARNING products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by . Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent Functions that relate in general to the systems are described in this system manual.
The information provided in this manual and in the system/function manuals supports you in
commissioning the systems.
Changes compared to previous version
Compared to the previous version, this manual contains the following change:
● New licensing conditions and copyright information of the Open Source Software
● The module features a switching cycle counter as of firmware version V1.1.0.
Conventions
The term "CPU" is used in this manual both for the CPUs of the automation system
and for interface modules of the ET 200MP distributed I/O system.
Please also observe notes marked as follows:
Note
A note contains important information on the product described in the documentation, on the
handling of the product or on the section of the documentation to which particular attention
should be paid.
Recycling and disposal
For environmentally friendly recycling and disposal of your old equipment, contact a certified
electronic waste disposal company and dispose of the equipment according to the applicable
regulations in your country. provides products and solutions with industrial security functions that support the
secure operation of plants, systems, machines and networks.
In order to protect plants, systems, machines and networks against cyber threats, it is
necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial
security concept. ' products and solutions constitute one element of such a concept.
Customers are responsible for preventing unauthorized access to their plants, systems