CPU. You can evaluate the error codes with the user program.
If the module is operated distributed with PROFIBUS DP in an ET 200MP system, you have
the option to read out diagnostics data with the instruction RDREC or RD_REC using data
record 0 and 1. The structure of the data records is available on the in the "Manual
for interface module IM 155-5 DP ST (6ES7155-5BA00-0AB0)Hardware version E01
Firmware version V1.0.0
Product function
I&M data Yes; I&M0 to I&M3
Engineering with
STEP 7 TIA Portal can be configured/integrated
as of version
V13 SP1 / -
STEP 7 can be configured/integrated as of version V5.5 SP3 / -
PROFIBUS as of GSD version/GSD revision V1.0 / V5.1
PROFINET as of GSD version/GSD revision V2.3 / -
Operating mode
MSO Yes
Supply 75 V DC/60 V AC (basic insulation) between the
backplane bus and the supply voltage L+; 250 V
AC between the channels and the supply voltage
L+; 250 V AC between the channels and the
backplane bus; 500 V AC between the channels
Insulation
Insulation tested with Between the channels: 2500 V DC; between the
channels and backplane bus: 2500 V DC; between
L+ and backplane bus 707 V DC (type
test)The following tables list the permissible number of switching cycles depending on the applied
voltage and current load. Different values apply in each case to resistive and inductive loads.
Table 6- 1 Switching capacity and service life of relay contacts for resistive loadThe dimension drawing of the module on the mounting rail, as well as a dimension drawing
with open front cover, are provided in the appendix. Always observe the specified
dimensions for installation in cabinets, control rooms, etc.The data records of the module have an identical structure, regardless of whether you
configure the module with PROFIBUS DP or PROFINET IO.
Dependencies for configuration with GSD file
When a GSD file is used to configure a module, dependencies can arise when "assigning the
parameters".
There are no dependencies for this module. You can assign the individual parameters in any
combination.
Parameter assignment in the user program
You have the option to reconfigure the module in RUN (e.g. the response of selected
channels to the CPU STOP state can be changed in RUN without having an effect on the
other channels).
Changing parameters in RUN
The WRREC instruction is used to transfer the parameters to the module using data records
64 to 79. The parameters set in STEP 7 are not changed in the CPU, which means the
parameters set in STEP 7 are valid again after a restart.
The parameters are only checked for plausibility by the module after the transfer.
STATUS output parameter
The module ignores errors that occurred during the transfer of parameters with the WRREC
instruction and continues operation with the previous parameter assignment. However, a
corresponding error code is written to the STATUS output parameter.
The description of the WRREC instruction and the error codes is available in the STEP 7
online help.
Operation of the module behind a PROFIBUS DP interface module
If the module is operated behind a PROFIBUS DP interface module, the parameter data
records 0 and 1 are not read back. You get the diagnostics data records 0 and 1 for the read
back parameter data records 0 and 1. You can find more information in the Interrupts section
of the PROFIBUS DP interface module device manual on the For the configuration as a 1 x 16-channel module, the parameters are located in data
records 64 to 79 and are assigned as follows:
● Data record 64 for channel 0
● Data record 65 for channel 1
● …
● Data record 78 for channel 14
● Data record 79 for channel 15
For the configuration as a 2 x 8-channel module, the module has 2 submodules with eight
channels each. The parameters for the channels are located in data records 64 to 71 and
are assigned as follows:
● Data records 64 to 71 for channels 0 to 7 (submodule 1)
● Data records 64 to 71 for channels 8 to 15 (submodule 2)
Address the respective submodule for data record transfer.The example in the figure below shows the structure of data record 64 for channel 0. The
structure of channels 1 to 16 is identical. The values in byte 0 and byte 1 are fixed and may
not be changed.
Enable a parameter by setting the corresponding bit to "1"Modules and Power Supply Modules of the SIMATIC , ET 200MP", Copyright
AG, 2013 - 2014 (hereinafter "Product"), the following Open Source Software is
used either unchanged or in a form that we have modified, and additionally the other License
Software noted below.
Liability for Open Source Software
Open Source Software is provided free of charge. We are liable for the Product including
Open Source Software contained in accordance with the license conditions applicable to the
Product. Any liability for use of Open Source Software beyond the program flow intended for
the Product is explicitly excluded.
We do not provide any technical support for the Product if it has been modified provides products and solutions with industrial security functions that support the
secure operation of plants, solutions, machines, equipment and/or networks. They are
important components in a holistic industrial security concept. With this in mind, ’
products and solutions undergo continuous development. recommends strongly
that you regularly check for product updates.