with "Thermal resistor Ni 100 Climatic" by ±0.1 KSmoothing time = Smoothing (k) x configured integration time
The following figure shows the time it takes for the smoothed analog value to reach
approximately 100 % depending on the set smoothing. This is valid for all signal changes at
the analog input.None (smoothing = 1 x integration time)
② Weak (smoothing = 4 x integration time) *
③ Medium (smoothing = 16 x integration time) *
④ Strong (smoothing = 32 x integration time) *
* The smoothing time can increase by 1 x integration time.
Figure C-5 Smoothing time depending on the set smoothing level
The following table shows the time it takes for the smoothed analog value to reach
approximately 100 % depending on the set smoothing and the set interference frequency
suppression.
Table C- 2 Smoothing time depending on the set smoothing level and interference frequency suppressionThe cycle times (1 ms, 1.04 ms and 1.25 ms) result from the configured interference
frequency suppression. The cycle time is independent of the number of configured analog
channels. The values for the analog input channels are detected sequentially in each cycle.
Reference
For more information on conversion time, cycle time and conversion method, refer to the Each analog value is entered left aligned into the tags. The bits marked with "x" are set to
"0".
Note
This resolution does not apply to temperature values. The digitalized temperature values are
the result of a conversion in the analog on-board I/O.The tables below set out the digitized representation of the input ranges separately for
bipolar and unipolar input ranges. The resolution is 16 bits.The following tables list the decimal and hexadecimal values (codes) of the possible current
measuring rangesThe following tables list the decimal and hexadecimal values (codes) of the possible
resistance-type sensor ranges.
Table C- 10 Resistance-type sensors of 150 Ω, 300 Ω and 600 ΩWith suitable parameter assignment, events that occur trigger a diagnostics entry and a
diagnostics interrupt.
Table C- 15 Measured values for wire break diagnostics
Format Parameter assignment Measu"Wire break" diagnostics enabled
• "Overflow/Underflow" diagnostics
enabled or disabled
("Wire break" diagnostics has a higher
priority than "Overflow/Underflow" diagnostics)
32767 7FFFH "Wire break" or "Cable break" diagnostics
alarm
• "Wire break" diagnostics disabled
• "Overflow/Underflow" diagnostics
enabled
-32767 8000 H • Measured value after leaving the underrange
• Diagnostics alarm "Low limit" violated
• "Wire break" diagnostics disabled
• "Overflow/Underflow" diagnostics
disabled
-32767 8000 H Measured value after leaving the underrangThe tables below set out the digitalized representation of the output ranges separately for
bipolar and unipolar ranges. The resolution is 16 bits.The tables below list the decimal and hexadecimal values (codes) of the possible voltage
output ranges.
Table C- 18 Voltage output range ±10 VThe tables below list the decimal and hexadecimal values (codes) of the possible current
output ranges.
Table C- 21 Current output range ±20 mAThis manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
his manual supplements the system manual of the automation system/ ET 200MP
distributed I/O system as well as the function manuals. This manual contains a description of
the module-specific information. The system-related functions are described in the system
manual. All system-spanning functions are described in the function manuals.
The information provided in this manual and the system manual enables you to commission
the CPU 1513-1 PN.
Conventions
STEP 7: In this documentation, "STEP 7" is used as a synonym for all versions of the
configuration and programming software "STEP 7 (TIA Portal)".
Please also observe notes marked as follows: provides products and solutions with industrial security functions that support the
secure operation of plants, systems, machines and networks.
In order to protect plants, systems, machines and networks against cyber threats, it is
necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial
security concept. ’ products and solutions only form one element of such a concept.
Customer is responsible to prevent unauthorized access to its plants, systems, machines