TAMAGAWA TS5208N569 TS5208N569 TS5208N569 TS5208N569 TS5208N569 TS5208N569

TS5208N569

Guang Zhou Lai Jie Electric Co.,LTD

Please contact with “Tommy” for the price

TS3095N2

AU6649N2101

TS3664N1E2

TS3630N1214E3

TS3641N21E6

TS5208N510

TS5208N576

TS4503N1022E200

TS3103N156

FACODER

TS3664N2E3

TS5013N60

TS3641N22E7

TS5208N68

TS5210N450

TS4503N1202E200

TS3103N178

TS3664N2E4

TS5013N61

TS3641N2E3

TS5212N351

TS5210N453

TS4503N1205E200

TS3103N255

TS3664N50

TS5016N60

TS3641N12E3

TS5212N510

The table below provides an overview of the diagnostic messages of
SM 322; DO 8 x 120/230 VAC/2 A ISOL.
Table 3- 33 Diagnostic messages of SM 322; DO 8 x AC 120/230 V/2 A ISOL
Diagnostics message LED Scope of diagnostics programmable
Watchdog timeout SF Module no
EPROM fault SF Module no
RAM fault SF Module noCauses of error and troubleshootingThe following table shows the diagnostic messages of SM 322; DO 8 x AC 120/230V/2 AISOL, causes oferror and troubleshooting.Table 3- 34 Diagnostic messages of SM 322; DO 8 x AC 120/230V/2 A ISOL, error causes andtroubleshootingDiagnostics message Error detection Possible cause of error To correct or avoid errorsWatchdog timeout Always Transient high electromagnetic
interference
Eliminate interference and cycle the
CPU power supply off and on
Defective module Replace the moduleEPROM fault Always Transient high electromagnetic
nterferenceEliminate interference and cycle theCPU power supply off and onDefective module Replace the moduleRAM fault Always Transient high electromagneticinterferenceEliminate interference and cycle theCPU power supply off and onDefective module Replacethe module3.32.3 SM 322; DO 8 x AC 120/230 V/2 A ISOL - InterruptsIntroductionThe SM 322; DO 8 x AC 120/230 V/2 A ISOL can trigger diagnostic interrupts.For detailed information on the OBs and SFCs mentioned below, refer to the STEP 7 OnlineHelp.Enabling interruptsThere is no default interrupt setting, i.e. interrupts are disabled if not set accordingly.Program the interrupt enable parameter in STEP 7.
When diagnostic interrupts are enabled, incoming error events (initial occurrence) and
outgoing error events (error is cleared) are reported by means of interrupt.The CPU interrupts user program execution in order to process diagnostics interrupt OB82.You can call SFC51 or 59 in OB82 in the user program to obtain detailed diagnostics data
from the module.Diagnostics data remain consistent until the program exits OB82. The module acknowledgesthe diagnostic interrupt when the program exits OB82.
Load restrictions in horizontal mounting positionIn horizontal mounting position, the module loads must be restricted so that two adjacentinputs or outputs do not exceed their rated load.
Load restrictions in vertical mounting positionIn vertical mounting position, the module loads must be restricted so that four adjacent inputsor outputs do not exceed their rated load.
6ES7322-1HH01-0AA0PropertiesThe SM 322; DO 16 x Rel. 120/230 V AC is characterized by the following properties:● 16 outputs, electrically isolated in groups of 8● Load voltage 24 to 120 V DC; 24 to 230 V AC● Suitable for AC/DC solenoid valves, contactors, motor starters, FHP motors and signallampshe internal 200-ms buffer capacitance discharges sufficient power after power off to allowthe user program to set a defined relay state.hannel number② Status display - green③ Backplane bus interfaceDimensions W x H x D (mm) 40 x 125 x 117Weight ca. 250 g
Module-specific dataSupports isochronous mode noNumber of outputs 16Cable length
• unshielded• shieldedmax. 600 m
max. 1000 mVoltages, currents, electrical potentialsRated power supply L+ to the relays 24 V DC
Total current of outputs (per group) max. 8 AElectrical isolation
• between channels and the backplane bus yes• between channels
in groups ofyes8
Maximum potential difference• Between Minternal and the power supply to relays and outputs 230 V AC
• Between outputs of different groups 500 V ACIsolation test voltage• between Minternal and the power supply to relays 500 V DC• between Minternal and the power supply to relays and outputs 1500 V AC• between outputs of different groups 2000 V ACCurrent consumption