TAMAGAWA TS5210N450 TS5210N450 TS5210N450 TS5210N450 TS5210N450 TS5210N450

TS5210N450

Guang Zhou Lai Jie Electric Co.,LTD

Please contact with “Tommy” for the price

TS5016N63

TS3643N2

TS5308N510

TS20E12

TS4503N2202E200

TS3134N21

TS3667N2E6

TS5016N64

TS3643N212E5

TS530N33E9

TS2151N121E9

TS4503N2036E501

TS3134N22

OIS1000CT3L5V108

TS3667N3E7

TS5017N60

TS3643N233E8

TS5312-N250

TS2151N141E9

TS4506N1202E200

TS3134N317

OSE10243158

TS3667N3E8

TS5019N60

TS3653N11E2

TS5313N122

TS2228N33E1

TS4507N1002E200

TS3134N52

OSE5K-6-12-108

TS3667N13E8

itching frequency
• with resistive load
• with inductive load to IEC 947-5-1, DC 13
• with lamp loadmax. 100 Hzmax. 0.5 Hzmax. 10 Hz
Internal limiting of the inductive shutdown voltage to typ. L + (- 53 V)Short circuit-proof output yes, electronic• Threshold typ. 1 A
Wiring of the actuators using a 20-pin front connector
6ES7327-1BH00-0AB0Properties
Properties of SM 327; DI 8/DO 8 x DC 24 V/0.5 A:● 8 digital inputs and 8 individually configurable inputsor outputs, isolated in groups of 16● Rated input voltage 24 V DC● Inputs suitable for switches and 2-/3-/4wire proximity switches (BEROs)● Output current 0.5 A● Rated load voltage 24 V DC● Outputscapable of driving solenoid valves, DC contactors and indicator lights● Dynamic change of parameters in RUN (CiR-compatible), separately at each channel● Readback of outputs.Use of the module with high-speed countersPlease note when using the module in combination with high-speed counters:NoteWhen using a mechanical contact to switch on the 24-V power supply toSM 327; DI 8/DO 8 x DC 24 V/0.5 A, its outputs will carry "1" signal for the duration of ca.50 µs, due to the circuit structure.Dimensions W x H x D (mm) 40 x 125 x 120
Weight ca. 200 gModule-specific dataSupports isochronous mode noNumber of inputs 8 digitalNumber of inputs/outputs 8, can be programmed separatelyCable length• unshielded
• shieldedmax. 600 mmax. 1000 mRated load voltage L+ 24 V DCNumber of simultaneously controlled inputs• horizontal mounting position
to 60 °C• vertical mounting positionto 40 °C16
16Total current of outputs (per group)• horizontal mounting positionto 40 °Cto 60 °C
• vertical mounting positionto 40 °C

max. 4 A
max. 3 A
max. 2 A
Electrical isolation
• between channels and the backplane bus yes
• between channels no
Isolation test voltage 500 V DC
Current consumption
• from the backplane bus
• from load voltage L+ (no-load)max. 60 mAmax. 20 mAPower loss of the module typ. 3 WStatus, interrupts, diagnosticsStatus display green LED per channelInterrupts noneDiagnostic functions none
Encoder selection dataInput voltage• Rated value• "1" signal• "0" signal
24 V DC
15 V to 30 V
- 30 V to + 5 VInput current
• "1" signal typ. 6 mA
Input delay• "0" to "1" transition• "1" to "0" transition1.2 ms to 4.8 ms1.2 ms to 4.8 msInput characteristicsto IEC 61131, type 1Connection of 2-wire BEROs• Permissible quiescent voltage• "1" signal min. L+ (-1.5 V)Output current
 "1" signalRated valuePermitted range0.5 A5 mA to 0.6 A• "0" signal (residual current) Max. 0.5 max. 500 μs
Load resistance range 48 Ω to 4 kΩLamp load max. 5 WWiring two outputs in parallel• for redundant load control supported• for performance increasenotsupported
Control of a digital input supportedSwitching frequency• with resistive load
• with inductive load to IEC 947-5-1, DC 13• with lamp loadmax. 100 Hz
max. 0.5 Hzmax. 10 HzInternal limiting of the inductive shutdown voltage to typ. L + (-54 V)Short circuit-proof output yes,electronic
• Threshold typ. 1 AWiring of the actuators using a 20pin front connector
The general procedure of programming digital modules is described in the chapterProgramming digital modulesThe table below lists the programmable parameters of SM 327; DI 8/DO 8 x DC 24 V/0.5 A,
including defaults.The defaults apply if you have not set any parameters in STEP 7.The comparison illustrates theparameters you can edit:● inSTEP 7● using SFC55 "WR_PARM"
● using SFB53 "WRREC" (for GSD, for example).