TAMAGAWA TS2651N141E78 TS2651N141E78 TS2651N141E78 TS2651N141E78 TS2651N141E78

TS2651N141E78

Guang Zhou Lai Jie Electric Co.,LTD

Please contact with “Tommy” for the price

TS5210N458

TS4503N1828E100

TS3103N302

OAH14BSD

TS3667N1E2

TS5013N63

TS3641N32

TS5213N550

TS5210N530

TS4503N2000E100

TS3103N40

OAS66

TS3667N11E2

TS5016N61

TS3641N38

TS5213N551

TS5210N54

TS4503N2070E100

TS3132N32

OAS66

TS1857N16EP

TS3667N2E5

TS5016N63

TS3643N2

TS5308N510

TS20E12

TS4503N2202E200

TS3134N21

TS3667N2E6

TS5016N64

TS3643N212E5

TS530N33E9

TS2151N121E9

TS4503N2036E501

TS3134N22

OIS1000CT3L5V108

TS3667N3E7

TS5017N60

TS3643N233E8

TS5312-N250

TS2151N141E9

TS4506N1202E200

TS3134N317

OSE10243158

TS3667N3E8

TS5019N60

TS3653N11E2

TS5313N122

TS2228N33E1

TS4507N1002E200

TS3134N52

OSE5K-6-12-108

TS3667N13E8

TS5013N68

TS3653N12E5

TS5320N632

TS2640N141E172

TS4507N1202E200

OSE5KN-6-12-108

TS3674N37

TS5013N69

TS3653N13E8

TS5420

TS2640N181E100

TS4507N1205E200

TS3166N43

TS3679N2E1

TS5208N131

TS3653N1E1

TS5641N150

TS2640N321E64

TS4507N1229E200

TS3212N32

RFH102422

TS3679N3E1

TS5208N111E78

TS3617N47E4

TS1508N211

TS2650N11E78

TS4507N2000E100

TS3214N12

RFH1024-22-1M-68

TS3682N1

TS3617N1E1

TS3624N1E1

Any measuring range selection per channel group
● Programmable diagnostics and diagnostic interrupt
● Programmable limit value monitoring for 8 channels
● Programmable hardware interrupt when limit is exceeded
● High-speed update of measured values at up to 4 channels
● Programmable hardware interrupt at end of cycle
● Electrically isolated from the CPU
● Supports parameter reassignment in RUN
Resolution
The resolution of measured values is independent of the selected integration time.
Diagnostics
For information on diagnostics messages at the "group diagnostics" parameter, refer to
chapter Diagnostic messages of analog input modules (Page 296).
Hardware interrupts
Hardware interrupts for channel groups 0 and 1 can be programmed in STEP 7. However,
set a hardware interrupt only for the first channel of a channel group, that is, either at
channel 0, or at channel 2
Terminal assignment
The diagrams below show various wiring options. These examples apply to all channels
(channel 0 to 7).
All 8 inputs are available as measurement channels if thermocouples are wired via reference
junctions which are regulated to 0 °C or 50 °C.
couple with external compensation
With this type of compensation, the temperature of the terminals at the reference junction is
established using a resistance thermometer Pt100 with a temperature range of -25 °C to
85 °C (see terminals 35 to 38).
Wire-break monitoring in 4-channel mode (hardware filter) at intervals of three seconds.
** In 8-channel software mode (software filter), series-mode rejection is reduced as follows:
• 50 Hz > 70 dB
• 60 Hz > 70 dB
• 400 Hz > 80 dB
*** The operational limit comprises only the basic error of the analog input at Ta = 25 °C and the total temperature error.
The total error must include the compensation error of the cold reference junction. Internal compensation of the reference
junction = max. 1.5 °C
External compensation of the reference junction = accuracy of the used external RTD ± 0.1 °C.
External compensation of the reference junction at which the reference junction is maintained at 0 °C or 50 °C = accuracy
of the temperature control of the reference junction.
**** Due to its small slope of approx. 0 °C to 40 °C, a lack of compensation for the reference junction temperature only has
a slight effect with thermocouple type B. With missing compensation and set measuring type "Compensation to 0 °C", the
deviation with thermocouple type B at measuring temperatures between:
• 700 °C and 1820 °C is < 0.5 °C
• 500 °C and 700 °C is < 0.7 °C.

If the reference junction temperature is approximately that of the module temperature, "internal compensation" should be
set. As a result, the error for the temperature range from 500 °C to 1820 °C is reduced to < 0.5 °C.
***** In 4-channel mode, the converted value settles to 100 % within 80 ms. The value determined in this process is set at
intervals of 3.3 ms (max. 10 ms).