 |
| Place of Origin: | Japan |
| Brand Name: | Tamagawa |
| Certification: | CE |
| Model Number: | TS5246N574 |
| Minimum Order Quantity: | 1pcs |
|---|---|
| Packaging Details: | carton |
| Delivery Time: | in stock |
| Payment Terms: | T/T, Western Union, MoneyGram |
| Supply Ability: | 100pcs/week |
| TAMAGAWA: | TAMAGAWA | TS5246N574: | TS5246N574 |
|---|---|---|---|
| Material: | Iron | Color: | Black |
| Temperature: | 40-120 | Dimension: | 40mm |
| Wire: | Wire |
TS5246N574
Guang Zhou Lai Jie Electric Co.,LTD
Please contact with “Tommy” for the price
TS4502N1202E200
TS4502N2000E100
TS4503N1000E200
TS4503N1007E200
TS4503N1022E100
TS4503N1022E200
TS4503N1202E200
TS4503N1205E200
TS4503N1828E100
TS4503N2000E100
TS4503N2070E100
TS4503N2202E200
TS4503N2036E501
TS4506N1202E200
TS4507N1002E200
TS4507N1202E200
TS4507N1205E200
TS4507N1229E200
TS4507N2000E100
TS4507N2070E100
TS4507N2405E200
TS4507N6205E200
TS4507N8029E200
TS4509N1002E200
TS4509N1202E200
TS4509N1831E200
TS4509N2002E200
TS4509N2405E200
TS4509N7000E100
TS4514N1021E200
TS4514N1407E200
TS4514N1828E200
TS4514N2002E200
TS4514N2405E200
TS4515N1202E200
TS4515N2405E200
TS4515N6000E200
TS4602N1000E200
TS4602N6321E100
TS4603N1000E100
TS4603N1000E200
TS4603N1532E200
TS4603N1700E200
TS4603N2002E200
TS4603N7002E200
TS1505N55?
TS1508N211
TS1508N255
TS1508N257
TS1508N260
TS1613N200
TS16N13E12
TS16N18E11
TS2013N191E26
TS2014N181E32
TS2014N311E32
TS2014N312E32
TS2018N303E51
TS20E12
TS20N2E11
TS2142N1E63
TS2151N1E26
TS2151N1E45
TS2151N11E45
TS2640N321E64
TS2641N31E64
TS2650N1E78
TS2650N11E78
TS2650N101E78
TS2651N111E78
TS2651N181E78
TS5000N532
TS5000N632
TS5003N632
TS5005N122
TS5007N122
TS5007N635
TS5208N500
TS5208N510
TS5208N530
TS5208N569
| Finding changes to the system hardware | The systemdependent |
| Testing the system configuration | You obtain information on the module (I data) from the module status dialog. |
| Error search and repair in the system | System-dependent information is configured in the properties dialog field of the module. |
information on the module is displayed here too.
Note
I&M data can only be written if the CPU is in the STOP operating mode.
The Al 6 x TC supports only I&M0 and I&M1 data.
The SM 331 is calibrated at the factory and complies with the specified accuracy values. As
a rule, there is no need to recalibrate the module.
With certain systems, it may be advisable or even a requirement laid down in standards (as
required by particular institutions in the food and beverage or pharmaceutical industries) to
recalibrate the module once it has been integrated into the system, for example, at
specific time intervals.
Particularly in systems where sensors detect and/or process relatively low voltages and/or
currents, it may be advisable to perform recalibration when the module is in the system
including all connected cables. This approach compensates any influence by cables and/or
temperature.
If you carry out a calibration procedure, new calibration values are detected and saved
retentively on the module. This means that the calibration values determined for the module
at the factory prior to delivery are not lost when users perform their own calibration work.
You can revert to these original calibration values at any time.
Note
The calibration values from each channel are saved retentively on the module for a specific
measuring range, which means they only apply to the measuring range in which the user
calibration work was performed.
If the parameters of a channel which has active user-calibration values are reassigned to
change the measuring range, the calibration values saved at the factory for this channel and
this measuring range are used from this point on.
However, the user-calibration values still remain in the memory; they are not overwritten until
the user calibrates the channel again. But if the original measuring range is reset for this
channel without the user performing the calibration procedure again, the user-calibration
values which have already been established become effective once more.
Requirements
The calibration function can only be used in a distributed installation and in conjunction with
the SIMATIC PDM ("Process Device Manager").
The following requirements must be met to use the module calibration functions: SIMATIC
PDM V6.0 + SP3 or higher + HF2 in conjunction with HSP158, or SIMATIC PDM V6.0 + SP4
or higher, and the EDD for the ET 200M,
"DP_IOSystem__ET200M_Module.Device", Version V1.1.10 or higher
User calibration is not permitted if the AI 6 x TC module is running in redundant mode.
The following diagrams show the sequence of a user calibration in SIMATIC PDM V6.0 +
SP5. More recent versions of SIMATIC PDM can deviate from the content of these
diagrams.
The module calibration function is launched in the SIMATIC PDM via <Device ⇒ Calibration>
for the selected module.
Figure 6-37 Calibration function
Once the calibration function has been launched, the calibration start screen appears. Each
time a new channel is selected, the module reads the following general data and calibration
values:
General data:
