TAMAGAWA TS5208N143 TS5208N143 TS5208N143 TS5208N143 TS5208N143 TS5208N143

TS5208N143

Guang Zhou Lai Jie Electric Co.,LTD

Please contact with “Tommy” for the price

TS2651N181E78

TS5000N532

TS5000N632

TS5003N632

TS5005N122

TS5007N122

TS5007N635

TS5208N500

TS5208N510

TS5208N530

TS5208N569

TS5208N576

TS5210N450

TS5210N453

TS5210N458??

TS5210N530

TS5210N54

TS5210N553

TS3684N1E3

TS3684N2E6

TS3684N3E8

TS3684N11E3

TS3684N12E6

TS3684N13E8

TS3617N1E3

TS3617N1E1

TS3617N1E2

TS3617N2E4

TS3617N2E5

TS3617N2E6

TS3617N2E7

TS3617N3E8

TS3617N3E9

TS3617N3E1

TS3617N11E3

TS3617N11E1

TS3617N11E2

TS3617N12E4

TS3617N12E5

TS3617N12E6

TS3617N12E7

TS3617N13E8

TS3617N13E9

TS3617N13E1

TS3653N1E1

TS3653N1E2

TS3653N1E3

TS3653N2E4

TS3653N2E5

TS3653N2E6

TS3653N3E7

TS3653N3E8

TS3653N3E9

TS3653N11E1

TS3653N11E2

TS3653N11E3

TS3653N12E4

TS3653N12E5

TS3653N12E6

TS3653N13E7

TS3653N13E8

TS3653N13E9

TS3103N40

TS3641N1E1

TS3641N2E3

TS3641N11E1

TS3641N12E3

TS3664N1E1

TS3664N1E2

TS3664N2E3

TS3664N2E4

TS3664N11E1

TS3664N11E2

TS3664N12E3

TS3664N12E4

TS3667N1E1

TS3667N1E2

TS3667N2E4

TS3667N1E3

TS3667N2E5

TS3667N2E6

TS3667N3E7

TS3667N3E8

user values
Offset: Currently active offset for the analog digital converter
● Gain: Currently active gain for the analog digital converter
● CJ Offset: Currently active temperature offset for the internal reference-temperature
sensor (only relevant for TC-IL thermocouples)
● TC Gain: Currently active gain for recording the temperature (only relevant for TC-IL,
TC-EL, TC-L00C, and TC-L50C thermocouples)
Slot address of the module
② Current system ID (HID)
③ Selection of the channel to be calibrated
④ Cancels the calibration function
⑤ Resets the calibration values of the selected channel to the factory settings
⑥ Starts user calibration for the selected channel
⑦ Current calibration values
Figure 6-38 User-calibration values
Now you can:
● Start user calibration for the selected channel
-> "User calibration" button
● Reset the calibration values set at the factory for the selected channel
-> "Reset to factory setting" button
● Cancel the calibration function
-> "Cancel" button
Note
If you reset the currently active channel to its factory settings, the original calibration
values saved on the module when it was delivered become valid again. Any usercalibration
values which may exist for this channel are then lost. You cannot restore these
user-calibration values.
User calibration
User calibration is started for the selected channel by pressing the "User calibration" button.
A 24 V load voltage must be applied at the module for calibration.
The user calibration function re-establishes the calibration values required by the selected
channel in accordance with the measuring range which has been programmed for that
channel.
Calibration can be executed in the CPU's RUN or STOP operating modes. Please note that
in the CPU's RUN operating mode, the module does not return any correct analog values to
the process for the duration of the calibration.
Note
While user calibration is ongoing, none of the module channels can handle new process
values.
• All analog input values of the module are set to 0x7FFF ("invalid analog value") until
calibration is complete.
• All channels indicate this status by means of a corresponding channel-diagnostic function
using the second type of diagnosis (see Section 1.7, "Diagnostics of the analog input
module SM 331; AI 6 x TC isolated").
The previously selected channel is calibrated using the calibration display which is output.
Calibration consists of several different steps, during which the individual calibration values
are determined.
● If a fault occurs during calibration or if new parameters are assigned to the module, the
calibration of the relevant channel is canceled and the most recently active calibration
values for the channel become effective once more. All of the calibration values recorded
up to this point are lost. The module can now handle the current process values once
again.
● Calibration can be canceled at any time once it has been started. Following cancelation,
the previously active calibration values take effect again and the calibration values
recorded up to this point are lost. The module can now handle the current process values
once again.
You must provide a voltage and/or temperature during user calibration. You do this by using
the appropriate external wiring and an external voltage/temperature transmitter. As shown in
the figure "User-calibration status", the "Instructions" field indicates the numbers of the pins
where the calibration stimulus can be applied. The first pin number corresponds to the
positive terminal, the second to the negative terminal. The accuracy of the calibration
depends on the accuracy of the voltage/temperature supplied. To ensure that the module
maintains the specified measuring accuracy following user calibration, the
voltage/temperature provided must demonstrate an accuracy at least twice that defined for
the module. Inaccurate voltages or temperatures will result in an incorrect calibration.

Here you will find instructions on how to carry out the currently active calibration step
② Here you will find information relating to the currently active calibration step
③ Here you will find information relating to the current status of the calibration procedure
④ Cancels the calibration function completely
⑤ Cancels the currently active calibration and returns to the calibration start screen
⑥ Skips the currently active calibration step
⑦ Confirms the currently active calibration step and proceeds to the next step
Figure 6-39 User-calibration status
Several different calibration steps are required to calibrate a channel, depending on the
measurement type which has been set. The "Status" field indicates whether the last
calibration step was completed with or without a fault. If a fault occurs while a calibration step
is being executed, the fault is indicated here and the calibration for that channel is canceled.
All calibration values recorded up to that point are deleted. The calibration values which were
active before the user-calibration function was launched take effect once more.