TAMAGAWA TS2651N141E78 TS2651N141E78 TS2651N141E78 TS2651N141E78 TS2651N141E78

TS2651N141E78

Please contact with “Tommy” for the price

TS5205N452

TS5205

N452

TS5207

TS5208

TS5212

TS5213

TS5214

TS5231

TS5217

TS5233

TS5150

TS5300

TS5100

TS5000

TS5080

TS5170

TS5410

TS5200N500

TS5146

TS5270

TS5610

TS5620

TS1857

TS5607

TS5668N20

TS5667N120

TS5667N420

TS5645

TS5647

TS5648

TS5643

TS2223

TS2224

TS2225

TS20E12

TS13E11

TS5308N616

TS2650N11E78

TS5420N60

TS5208N131

TS3462N1E76

48-2500P8-L6-5VC/T-L3-12V

TS-5016N-60

TS5214N561

TS5214N510

TS2014N182E32

TS3653N2E5

TS5320N510

TS5016N-60

TS5016N60

TS5305N616

TS5008N12238

TS5214N564

TS5212N569

TS2651N111E78

TS2014N181E32

TS-5208N130

TS5207N76

TS5246N160

TS5312N616-2000C-T

TS5312N616

Operational limit (across entire temperature range, relative to the measurement range end value in the selected input
range)
• Voltage input 0 V to 10 V ± 0.7 %
• Resistance input 10 kΩ ± 3.5 %
• Temperature input Pt 100 ± 1 %
Basic error limit (operational limit at 25 °C, relative to the measurement range end value in the selected input range)
• Voltage input 0 V to 10 V ±0.5 %
• Resistance input 10 kΩ ± 2.8 %
• Temperature input Pt 100 ± 0.8 %
Temperature error (relative to input range) ± 0.01 %/K
Linearity error (relative to input range) ±0.05 %
Repeat accuracy (in settled state at 25 °C, relative to input range) ± 0.05 %
Interference frequency suppression, error limits of outputs
Crosstalk between outputs > 88 dB
Operational limit (across entire temperature range, relative to measurement range end value in the selected output range)
• Voltage output ± 1.0 %
Basic error limit (operational limit at 25 °C, relative to the measurement range end value in the selected output range)
• Voltage output ± 0.85 %
Temperature error (relative to output range) ± 0.01 %/K
Linearity error (relative to output range) ± 0.01 %
Repeat accuracy (in transient state at 25 °C, relative to output range) ± 0.01 %
Output ripple; range 0 Hz to 50 kHz (relative to output range) ± 0.1 %
Status, interrupts, diagnostics
Interrupts none
Diagnostic function none

Encoder selection data
Input ranges (rated values) / input impedance
• Voltage 0 V to 10 V 100 kΩ
• Resistance 10 kΩ 10 MΩ
• Temperature Pt 100 10 MΩ
Maximum voltage at voltage input (destruction limit) max. 20 V continuous; 75 V for max. duration of 1 s
(duty factor 1:20)
Wiring of the signal transmitters
• for voltage measurement
• for resistance measurement
with 2-wire connection
with 3-wire connection
with 4-wire connection
supported
supported
supported
supported
Characteristics linearization
• for resistance thermometers
programmable
Pt 100 (Climatic range)
Technical unit of data formats degrees Centigrade
Actuator selection data
Output range (rated value)
• Voltage 0 V to 10 V
Load impedance (in the rated output range)
• For voltage outputs
– capacitive load
min. 2.5 kΩ *
max. 1.0 µF
Voltage output
• Short-circuit protection
• Short-circuit current
Yes
max. 30 mA
Destruction limit against external voltages/currents
• Voltage at outputs to MANA max. 15 V, continuous
Wiring of the actuators
• for voltage output
2-wire connection
4-wire connection (measuring line)
using a 20-pin front connector
supported
not supported
* the error limits specified for the outputs are only valid when there is a high-ohm connection. In the entire load resistance
range, an additional error of <0.9 % can result.
For general information on programming analog modules, refer to the chapter Programming
analog modules (Page 294).
The table below provides an overview of configurable parameters, including defaults:
Table 6- 40 Summary of parameters SM 334; AI 4/AO 2 x 12 Bit
Measurement
• Measurement type disabled RTD-4L
V
R-4L
RTD-4L
Voltage
Resistance
(4-wire connection)
Thermal resistance
(linear, 4-wire connection)
dynamic Channel
• Measuring range 0 V to 10 V
10000 Ω
Pt 100 Klima
Pt 100 Klima
Output
• Output type
• Output range
disabled
Voltage
0 V to 10 V