TAMAGAWA TS5778N155 TS5778N155 TS5778N155 TS5778N155 TS5778N155 TS5778N155

TS5778N155

Guang Zhou Lai Jie Electric Co.,LTD

Please contact with “Tommy” for the price

TS3667N3E7

TS3667N3E8

TS3667N11E1

TS3667N11E2

TS3667N12E4

TS3667N11E3

TS3667N12E5

TS3667N12E6

TS3667N31E7

TS3667N13E8

TS3624N1E1

TS3624N1E2

TS3624N2E3

TS3624N2E4

TS3624N3E5

TS3624N3E6

TS3630N1E1

TS3630N1E2

TS3630N2E3

TS3630N2E4

TS3630N3E5

TS3630N3E6

TS3630N1303E9

TS3630N1306

TS3630N11E1

TS3630N11E2

TS3630N12E3

TS3630N12E4

TS3630N13E5

TS3630N13E6

FA-CODER

TS5214N566

TS5205N450

TS5205N454

TS5205

N450

TS5205

N454

TS5205N452

TS5205

N452

TS5207

TS5208

TS5212

TS5213

TS5214

TS5231

TS5217

TS5233

TS5150

TS5300

TS5100

TS5000

TS5080

TS5170

TS5410

TS5200N500

TS5146

TS5270

TS5610

TS5620

TS1857

TS5607

TS5668N20

TS5667N120

TS5667N420

Electrically isolated from load voltage (not for 2-wire transducers)

For information on diagnostics messages at the "group diagnostics" parameter, refer to
chapter Diagnostic messages of analog input modules (Page 296).
Hardware interrupts
Hardware interrupts for channel groups 0 and 1 can be programmed in STEP 7. However,
set a hardware interrupt only for the first channel of a channel group, that is, either at
channel 0, or at channel 2
Wiring of the signal transmitters
• for voltage measurement
• for current measurement
as 2-wire transducer
as 4-wire transducer
• Load of the 2-wire transducer at L+ = DC 24 V

The analog input module has measuring range modules. The measurement type and range
is configured at the "measuring range" parameter in STEP 7.
The default setting of the module STEP 7 is "voltage" measurement with "± 10V" range. You
can use those default settings without having to program the SM 331;
AI 8 x 14 Bit High Speed in STEP 7.
You may have to change the position of the measuring range module to suit the
measurement type and range. See table Setting measuring methods and ranges of analog
input channels. The settings are also printed on the module. Mark the position of the
measuring range module on the front door (see figure).
The channels of SM 331; AI 8 x 14 Bit High Speed are arranged in four groups of two
channels. You can assign parameters only to one channel group.
SM 331; AI 8 x 14 bits High Speed is equipped with one measuring range module per
channel group.
The table below shows the relevant configuration of channel groups. The channel group
number is required to program SFC parameters in the user program.
Table 6- 14 Assignment of SM 331; AI 8 x 14 bits High Speed channels to channel groups

For information on programming analog modules, refer to the chapter Programming analog
modules
Enable
• Diagnostics interrupt
• Process interrupt when limit
exceeded
yes/no
yes/no
no
no
dynamic Module
Fast Mode (can only be set if the
331-7HF01 is included for isochronous
operation in the DP slave
Reproducible reaction times (i.e. of the same length) are achieved in a SIMATIC system by
means of a constant DP bus cycle, and synchronization of the single cyclic processes
outlined below:
● Independent user program cycle. The length of the cycle time may vary due to non-cyclic
program branching.
● Independent and variable DP cycle on the PROFIBUS subnet
● Cyclic operation of the backplane bus of the DP slave.
● Cyclic signal preparation and conversion at the electronic modules of the DP slave.
The constant DP cycle runs in synchronism and at the same length. The CPU run levels
(OB61 to OB64) and isochronous IO are synchronized with this cycle. I/O data are therefore