TAMAGAWA TS5208N131 TS5208N131 TS5208N131 TS5208N131 TS5208N131 TS5208N131

TS5208N131

Guang Zhou Lai Jie Electric Co.,LTD

Please contact with “Tommy” for the price

TS5013N69

TS2650N101E78

TS4126N1017E235

TS1981N56E19

TS3653N13E9

TS5N2E18

TS3630N1E1

TS5013N61

TS2651N111E78

TS4127N1017E215

TS1982N126E6

TS3653N44E8

TS3630N1E2

TS5013N89

TS2651N181E78

TS4127N1017E235

TS1982N128E6

8001231S

TS3653N4E12

TS5013N64

TS3630N2E3

TS5016N

TS5000N532

TS4231N6E17

TS1982N53E6

800123-2R

TS3653N14E12

TS5420N60

TS3630N2E4

TS5016N60

TS5000N632

TS4231N6E17

TS1982N56E18

TS3653N58E5

TS5778N155

TS3630N3E5

TS5003N632

TS4244N10E24

TS1982N56E18

800123-R-F

TS3653N65E27

TS5208N23

TS3630N101E2

TS5017N56

TS5005N122?

TS4244N3E24

TS1983N146E5

TS3653N81E27

TS2025N471E69

TS3630N102E4

TS5017N60

TS5007N122

TS4502N1000E200

TS1983N146E5

TS3653N78E5

TS2014N181E32

TS3630N22E3

TS5108-N153-5V

TS5007N635

TS4502N1202E200

TS252N30E1

AU6270N103E63

TS3653N94E5

TS5208N141E78

TS3630N22E4

TS5146N10

TS5208N500

TS4502N2000E100

TS3503N11E43

TS3653N181E8

TS3684N1E3

TDPmin 3.5 ms
Diagnostics interrupt max. 4 x TDP
Fast Mode (only possible with 6ES7331-7HF01-0AB0)
Filter and processing time TWE between reading actual value and writing the results to the
transfer buffer (diagnosis not selectable)
max. 625 μs
including an input delay time of
You can accelerate the cycle of your DP system by setting "Fast Mode." However, this is at
the expense of diagnostics: Diagnostics functions will be disabled in this operating mode.
The minimum Ti value of 875 µs which you can set in HW Config is derived from the defined
TWE value plus calculation and transfer times required by the IM 153.
The specified TDPmin value is determined by the size of the DP slave/IM 153 configuration: Of
the diverse installed modules, the slowest always determines the time TDPmin.
Note
When operated in "isochronous" mode, the modules automatically sets "Integration time:
none/interference frequency", irrespective of parameter settings in STEP 7. none /
interference frequency". "Process interrupt" functionality is not available in "isochronous"
mode.
er and processing times
The same time conditions always apply, regardless of the number of configured channels.
The time relative to the clock signal for reading a specific channel is calculated according to
the formula:
TWE_CH = (channel number +1) x 52 µs + tv; tv = 119 to 209 µs
The module starts with the analog-to-digital conversion of channel 7, and saves the result
internally. Next, it converts channels 6...0 sequentially at intervals of 52 ms and in the same
way. After an additional internal processing time, it outputs the result of all converted
channels to the backplane bus interface where it can be fetched by the CPU.
Further information
You can find additional information on isochronous mode in the online help for STEP 7, and
in the operating instructions Distributed I/O System ET 200M
You should wire unused channels as shown in the following table. This optimizes
interference immunity of the analog input module.
Measuring range M+/ M- M_ana
Voltage short-circuit connect with MCurrent
/ 4-wire transducer leave open connect with MCurrent
/ 2-wire transducer leave open connect with M
As certain programmed inputs may remain unused due to the channel group configuration,
make allowances for the special features of these inputs outlined below in order to be able to
use the diagnostics functions at these used channels:
● Measuring range 1 V to 5 V: wire the used input and unused input of the same channel
group in parallel