 |
| Place of Origin: | Japan |
| Brand Name: | Tamagawa |
| Certification: | CE |
| Model Number: | TS5210N458 |
| Minimum Order Quantity: | 1pcs |
|---|---|
| Packaging Details: | carton |
| Delivery Time: | in stock |
| Payment Terms: | T/T, Western Union, MoneyGram |
| Supply Ability: | 100pcs/week |
| TAMAGAWA: | TAMAGAWA | TS5210N458: | TS5210N458 |
|---|---|---|---|
| Japan: | Japan | Material: | Iron |
| Color: | Bllack | Temperature: | 30-90 |
| Dimension: | 80mm | Wire: | Wire |
TS5210N458
| may be used. The thermocouple module provides for use of a 0° C referenced or 50° C referenced terminal block. |
In the presence of radiated radio frequency of 970 MHz to 990 MHz, the accuracy of the SM 1231 AI 4 x 16 bit TC may |
| Selection tables for the SM 1231 thermocouple The ranges and accuracy for the different thermocouple types supported by the SM 1231 Thermocouple signal module are shown in the table below. |
Thermocouple values above the over-range minimum value are reported as 32767. 3 Internal cold junction error is ±1.5°C for all ranges. This adds to the error in this table. The module requires at least 30 |
| hermocouple values below the under-range minimum value are reported as -32768. | minutes of warmup time to meet this specification. |
Guang Zhou Lai Jie Electric Co.,LTD
Please contact with “Tommy” for the price
TS3653N2E5
TS5320N510
TS5016N-60
TS5016N60
TS5305N616
TS5008N12238
TS5214N564
TS5212N569
TS2651N111E78
TS2014N181E32
TS-5208N130
TS5207N76
TS5246N160
TS5312N616-2000C-T
TS5312N616
TS5217N530
DIH35-5000C/T-P8-L6-5V
OIH100-1024C/T-P2-12V
TS5233N430
DIH48-6000C/T-P8-L6-5V
TS5246N430
TS1857N112
TS5213N551
TS5214N364
TS5312N512-2000C/TOSE.5KN-6-12-108
TS5146N11
BKO-NC6214
TS5214N500
48-2500PA-L6-5V
TS5205N4540IH60-8192C/T-P8-L6-5V
TS3699N172
TS3653N3E8
1510N122
TS3653N1E2
TS5667N120
TS3624N2E3
TS3738N1E7
be degraded. To maintain module resolution and accuracy when 400 Hz rejection is selected, the integration time is 10 ms. This
selection also rejects 100 Hz and 200 Hz noise. It is recommended for measuring thermocouples that a 100 ms integration time be used. The
use of smaller integration times will increase the repeatability error of the temperature
readings.
Note
After power is applied, the module performs internal calibration for the analog-to-digital
converter. During this time the module reports a value of 32767 on each channel until valid
data is available on that channel. Your user program may need to allow for this initialization
time. Because the configuration of the module can vary the length of the initialization time,
you should verify the behavior of the module in your configuration. If required, you can
include logic in your user program to accommodate the initialization time of the moduleA representation of the analog values of thermocouples type J is shown in the table below.
Table A- 146 Representation of analog values of thermocouples type J 1 Faulty wiring (for example, polarity reversal, or open inputs) or sensor error in the negative
range (for example, wrong type of thermocouple) may cause the thermocouple module to
signal underflowThe overflow, underflow and low voltage diagnostic alarm information will be reported in the analog data values even if
the alarms are disabled in the module configuration.
2 For resistance ranges underflow detection is never enabled.
3 When wire break alarm is disabled and an open wire condition exists in the sensor wiring, the module may report
random values.
The SM 1231 RTD analog signal module measures the value of resistance connected to the
module inputs. The measurement type can be selected as either "Resistor" or "Thermal
resistor".
● "Resistor": The nominal range full scale value will be decimal 27648.
● "Thermal resistor": The value will be reported in degrees multiplied by ten (for example,
25.3 degrees will be reported as decimal 253).
The SM 1231 RTD module supports measurements with 2-wire, 3-wire and 4-wire
connections to the sensor resistor① Loop-back unused RTD inputs
② 2-wire RTD ③ 3-wire RTD ④ 4-wire RTD
NOTE: Note: Connectors must be gold. See Appendix C, Spare Parts for order number. The RTD unused channels can be deactivated. No error will occur if an unused channel is
deactivated.
