TAMAGAWA TS5016N63 TS5016N63 TS5016N63 TS5016N63 TS5016N63 TS5016N63 TS5016N63

TS5016N63

Guang Zhou Lai Jie Electric Co.,LTD

Please contact with “Tommy” for the price

TS3624N3E5

TS3624N3E6

TS3630N1303E9

TS3630N1309E5

TS3630N1306

TS3630N1E1

TS3630N1E2

TS3630N2E3

TS3630N2E4

TS3630N3E5

TS3630N101E2

TS3630N102E4

TS3630N22E3

TS3630N22E4

TS3631N1E1

TS3636N6

TS3641N1E1

TS3641N21E6

TS3641N22E7

TS3641N2E3

TS3641N12E3

TS3641N32

TS3641N38

TS3643N2

TS3643N212E5

TS3643N233E8

TS3653N11E2

TS3653N12E5

TS3653N13E8

"Modify now" immediately changes the value for the selected addresses for one scan
cycle.

"Modify with trigger" changes the values for the selected addresses.
This function does not provide feedback to indicate that the selected addresses were
actually modified. If feedback of the change is required, use the "Modify now" function.
● "Enable peripheral outputs" disables the command output disable and is available only
when the CPU is in STOP mode.
To monitor the tags, you must have an online connection to the CPU. ing a trigger when monitoring or modifying PLC tags
Triggering determines at what point in the scan cycle the selected address will be monitored
or modified. Triggering determines at what point in the scan cycle the selected address will be monitored
or modified. Continuously collects the data
Permanent: Continuously collects the data at the start of the scan cycle, after
the CPU reads the inputs
At scan cycle start
Once: Collects the data at the start of the scan cycle, after the CPU reads the
inputs
Permanent: Continuously collects the data at the end of the scan cycle, before
the CPU writes the outputs
At scan cycle end
Once: Collects the data once at the end of the scan cycle, before the CPU
writes the outputs
At transition to Permanent: Continuously collects data when the CPU transitions to STOP
STOP Once: Collects the data once after the CPU transitions to STOP For modifying a PLC tag at a given trigger, select either the start or the end of cycle.
● Modifying an output: The best trigger event for modifying an output is at the end of the
scan cycle, immediately before the CPU writes the outputs.
Monitor the value of the outputs at the beginning of the scan cycle to determine what
value is written to the physical outputs. Also, monitor the outputs before the CPU writes
the values to the physical outputs in order to check program logic and to compare to the
actual I/O behavior.

Modifying an input: The best trigger event for modifying an input is at the start of the
cycle, immediately after the CPU reads the inputs and before the user program uses the
input values.
If you are modifying inputs the start of the scan cycle, you should also monitor the value
of the inputs at the end of the scan cycle to ensure that the value of the input at the end
the scan cycle has not changed from the start of the scan cycle. If there is a difference in
the values, your user program may be writing to an input in error.
To diagnose why the CPU might have gone to STOP, use the "Transition to STOP" trigger to
capture the last process values. The watch table allows you to write to the outputs when the CPU is in STOP mode. This
functionality allows you to check the wiring of the outputs and verify that the wire connected
to an output pin initiates a high or low signal to the terminal of the process device to which it
is connected. You can change the state of the outputs in STOP mode when the outputs are enabled. If the
outputs are disabled, you cannot modify the outputs in STOP mode.
● To enable the modification of the outputs in STOP, select the "Enable peripheral outputs"
option of the "Modify" command of the "Online" menu, or by right-clicking the row of the
Watch table.
You cannot enable outputs in STOP mode if you have configured distributed I/O,. An
error is returned when you try to do this.
● Setting the CPU to RUN mode disables "Enable peripheral outputs" option.
● If any inputs or outputs are forced, the CPU is not allowed to enable outputs while in
STOP mode. The force function must first be cancelledA force table provides a "force"