TAMAGAWA TS5667N650 TS5667N650 TS5667N650 TS5667N650 TS5667N650 TS5667N650

TS5667N650

Guang Zhou Lai Jie Electric Co.,LTD

Please contact with “Tommy” for the price

TS3617N3E8

TS3617N3E9

TS3617N3E1

TS3617N11E3

TS3617N11E1

TS3617N11E2

TS3617N12E4

TS3617N12E5

TS3617N12E6

TS3617N12E7

TS3617N13E8

TS3617N13E9

TS3617N13E1

TS3653N1E1

TS3653N1E2

TS3653N1E3

TS3653N2E4

TS3653N2E5

TS3653N2E6

TS3653N3E7

TS3653N3E8

TS3653N3E9

TS3653N11E1

TS3653N11E2

TS3653N11E3

TS3653N12E4

TS3653N12E5

TS3653N12E6

TS3653N13E7

ADDR_MAIL_SERVER 1 Static DWord IP address of the mail server: You must assign each IP
address fragment as an octet of two 4-bit hexadecimal
characters. If the IP address fragment = decimal value 10
which equals hexadecimal value A, then you must enter
"0A" for that octet.
For example: IP address = 192.168.0.10
ADDR_MAIL_SERVER = DW#16#C0A8000A, where:
 192 = 16#C0,
 168 =16#A8
 0 = 16#00
 10 = 16#0A
WATCH_DOG_TIME 1 Static Time The maximum time allowed for TM_MAIL to establish a
server connection. If this time is exceeded, then TM_MAIL
execution ends with an error.
The actual time delay until TM_MAIL ends and the error is
issued may exceed the WATCH_DOG_TIME, because of
the additional time required for the disconnect operation.
At first you should set a time of 2 minutes. This time can be
much smaller for an ISDN phone connection.
USERNAME 1 Static String Mail account user name: STRING data with a maximum
length 180 characters.
PASSWORD 1 Static String Mail server password: STRING data with a maximum length
180 charactersSender address: STRING with a maximum length of 240
characters
SFC_STATUS 1 Static Word Execution condition code of the called communication
blocks
1 The values of these parameters are not modified at every call of TM_MAIL. The values are assigned in the TM_MAIL
instance data block and are only referenced once, on the first call of TM_MAIL.
TM_MAIL supports the SMTP AUTH LOGIN authentication method. For information on this
authentication method, please refer to the manual of the mail server or the website of your
internet service provider.
The AUTH LOGIN authentication method uses the TM_MAIL USERNAME and PASSWORD
parameters to connect with the mail server. The user name and password must be
previously set up on an email account at an email server.
If no value is assigned for the USERNAME parameter, then the AUTH LOGIN authentication
method is not used and the email is sent without authentication.
he characters "TO_S:", "CC:" and "FROM:" must be entered, including the colon
character.

A space character and an opening angle bracket "<" must precede each address. For
example, there must be a space character between "TO_S:" and <email address>.
● A closing angle bracket ">" must be entered after each address.
● A comma character "," must be entered after each email address for the TO_S: and CC:
addresses. For example, the comma after the single email address is required in "TO_S:
<email address>,".
● Only one email address may be used for the FROM: entry, with no comma at the end.
Because of run-time mode and memory usage, a syntax check is not performed on the
TM_MAIL TO_S:, CC: and FROM: data. If the format rules above are not followed exactly.
The SMTP email server transaction will fail. The execution condition codes returned by TM_MAIL can be classified as follows:
● W#16#0000: Operation of TM_MAIL was completed successfully
● W#16#7xxx: Status of TM_MAIL operation
● W#16#8xxx: An error in an internal call to a communication device or the mail server
The follog table shows the execution condition codes of TM_MAIL with the exception of
the error codes from internally called communication modules.