TAMAGAWA TS5667N420 TS5667N420 TS5667N420 TS5667N420 TS5667N420 TS5667N420

TS5667N420

Guang Zhou Lai Jie Electric Co.,LTD

Please contact with “Tommy” for the price

TS4514N2002E200

TS4514N2405E200

TS4515N1202E200

TS4515N2405E200

TS4515N6000E200

TS4602N1000E200

TS4602N6321E100

TS4603N1000E100

TS4603N1000E200

TS4603N1532E200

TS4603N1700E200

TS4603N2002E200

TS4603N7002E200

TS1505N55 

TS1508N211

TS1508N255

TS1508N257

TS1508N260

TS1613N200

TS16N13E12

TS16N18E11

TS2013N191E26

TS2014N181E32

TS2014N311E32

TS2014N312E32

TS2018N303E51

TS20E12

TS20N2E11

TS2142N1E63

TS2151N1E26

TS2151N1E45

Invalid Time value Note that the T_COMBINEinstruction in the Extended Instructions equates to the CONCAT_DATE_TODfunction in SCL.

OUT OUT DTL DTL value Use the clock instructions to set and read the CPU system clock. The data type DTL
(Page 96) is used to provide date and time values.
WR_SYS_T (Write System Time) sets the CPU time of day clock with a
DTL value at parameter IN. This time value does not include local time
zone or daylight saving time offsets.
ret_val := RD_SYS_T(
out=>_DTL_out);
RD_SYS_T (Read System Time) reads the current system time from
the CPU. This time value does not include local time zone or daylight
saving time offsets.
ret_val := RD_LOC_T(
out=>_DTL_out);
RD_LOC_T (Read Local Time) provides the current local time of the
CPU as a DTL data type. This time value reflects the local time zone
adjusted appropriately for daylight saving time (if configured).
Time of day to set in the CPU system clock
RET_VAL OUT Int Execution condition code
OUT OUT DTL RD_SYS_T: Current CPU system time
RD_LOC_T: Current local time. including any adjustment for
daylight saving time, if configured
● The local time is calculated by using the time zone and daylight saving time offsets that
you set in the device configuration general tab "Time of day" parameters.
● Time zone configuration is an offset to UTC or GMT time.
● Daylight saving time configuration specifies the month, week, day, and hour when
daylight saving time begins.

Standard time configuration also specifies the month, week, day, and hour when standard
time begins.
● The time zone offset is always applied to the system time value. The daylight saving time
offset is only applied when daylight saving time is in effect.
Note
Daylight saving and standard start time configuration
The "Time of day" properties for "Start for daylight saving time" of the CPU device
configuration must be your local time.
Condition codes: ENO = 1 means no error occurred. ENO = 0 means an execution error
occurred, and a condition code is provided at the RET_VAL output.
Table 8- 11 Condition codes
RET_VAL (W#16#....) Description
0000 The current local time is in standard time.
0001 Daylight saving time has been configured, and the current local time is in daylight saving
time.
8080 Local time not available
8081 Illegal year value
8082 Illegal month value
8083 Illegal day value
8084 Illegal hour value
8085 Illegal minute value
8086 Illegal second value
8087 Illegal nanosecond value
80B0 The real-time clock has failed.
Extended instructions
8.1 Date and time-of-day
Programmable controller
System Manual, 04/2012, A5E02486680-06 251
8.1.3 Run-time meter instrThe RTM (Run Time Meter) instruction can set, start, stop, and
read the run-time hour meters in the CPU.
Run-time meter number: (possible values: 0..9)
MODE IN Byte RTM Execution mode number:
 0 = Fetch values (the status is then written to CQ and the
current value to CV)